PaperModelers.com

Go Back   PaperModelers.com > Card Models > Model Builds > The Armory

Reply
 
Thread Tools Display Modes
  #11  
Old 01-06-2020, 07:12 AM
modelperry's Avatar
modelperry modelperry is offline
Member
 
Join Date: Feb 2008
Location: Burlington, Iowa
Posts: 2,819
Total Downloaded: 10.41 MB
Just one picture today. The front axle and steering installation.

Of note:

I cut the mounting post down and heat swaged the end to trap the axle in place. Right before this I had to trim the mounting bracket sides just a touch to improve clearance and allow just a touch of axle pivot.

The A-frame axle brace was a touch too short so I added a little bit to the center rear tang where it attaches to the bracket on the bottom of the driveline tunnel.

While I did not attempt it, I think it would be a relatively straight forward task to make the steering position-able.

greg
Attached Thumbnails
Case VAI tractor - Answer-img_20200105_174105.jpg  
__________________
In dry dock: ? In factory: CWS T-1. In hanger: Fokker triplanes? under construction: ?
Reply With Quote
  #12  
Old 01-13-2020, 08:41 AM
modelperry's Avatar
modelperry modelperry is offline
Member
 
Join Date: Feb 2008
Location: Burlington, Iowa
Posts: 2,819
Total Downloaded: 10.41 MB
Next step is to dress the engine, right side first. I added wiring to the distributor.

Then I did the front of the engine. Radiator hoses were called out but no patterns provided. Note that the lower hose was a bear to install. The radiator mounts installed earlier had to be removed because they positioned the radiator too high (they were good for longitudinal position though.

Next up was the left side engine components (intake and exhaust). Intake and exhaust tube patterns were provided and are accurate.

Finally the hood was fashioned. pieces at the front do not really line up with the top hood well. The framing for the curved petal portion needed to be modified to allow fit over the radiator (this confirms the need to modify the radiator mounts). The rear panel also needed trimmed a little to improve hood fit.

Now all I have to do is wheels but this won't happen soon due to business travel obligations.

greg
Attached Thumbnails
Case VAI tractor - Answer-img_20200105_175247.jpg   Case VAI tractor - Answer-img_20200107_201710.jpg   Case VAI tractor - Answer-img_20200107_202741.jpg   Case VAI tractor - Answer-img_20200108_210547.jpg   Case VAI tractor - Answer-img_20200110_185740.jpg  

Case VAI tractor - Answer-img_20200110_191617.jpg   Case VAI tractor - Answer-img_20200111_191254.jpg   Case VAI tractor - Answer-img_20200111_191304.jpg  
__________________
In dry dock: ? In factory: CWS T-1. In hanger: Fokker triplanes? under construction: ?
Reply With Quote
  #13  
Old 01-13-2020, 08:58 PM
TramFan's Avatar
TramFan TramFan is offline
Member
 
Join Date: Oct 2016
Location: Wilderness area, West Cape, South Africa
Posts: 283
Total Downloaded: 542.99 MB
Very nice tractor.
Reply With Quote
  #14  
Old 01-14-2020, 03:26 AM
Kevin WS's Avatar
Kevin WS Kevin WS is offline
Eternal Member
 
Join Date: Aug 2010
Location: Currently Southern Africa.
Posts: 7,121
Total Downloaded: 425.92 MB
A great model - tractors make nice subjects!
__________________
The SD40 is 55 now!
Reply With Quote
  #15  
Old 01-21-2020, 01:51 PM
modelperry's Avatar
modelperry modelperry is offline
Member
 
Join Date: Feb 2008
Location: Burlington, Iowa
Posts: 2,819
Total Downloaded: 10.41 MB
All kinds of wheels

These built up a little differently than some. The front wheel ribs are all disks with edge pieces attached for the tread. Then there are the conical webs between them to represent the rest of the tire contour. The finished product looks a little slab sided but its been a while since I've seen any sort of ribbed tire like this on any tractor.

The front axle spindle parts ended up with judicious amounts of superglue for strength.

Rear tires were quite involved. each tire has a left and right half and they are directional so care must be taken to preserve this when installing the inner wheel rim.

The tread blocks were akin to tank tracks. 34 per side That's all I have to say about them.

Other wise no fit issues. But painting of tires necessary to cover some white parts and to provide uniform tire color.

I did have to mount the rear tires with a little space between them and the main axle housing to properly clear the fenders.

With that the build is complete. This is a good intermediate level model for someone who wants to graduate from easier projects or wants a little breather from a more difficult one.
greg
Attached Thumbnails
Case VAI tractor - Answer-img_20200117_184701.jpg   Case VAI tractor - Answer-img_20200118_184429.jpg   Case VAI tractor - Answer-img_20200118_184853.jpg   Case VAI tractor - Answer-img_20200118_185623.jpg   Case VAI tractor - Answer-img_20200119_192725.jpg  

Case VAI tractor - Answer-img_20200119_195018.jpg   Case VAI tractor - Answer-img_20200120_121533.jpg   Case VAI tractor - Answer-img_20200120_121543.jpg   Case VAI tractor - Answer-img_20200120_121550.jpg   Case VAI tractor - Answer-img_20200120_121557.jpg  

Case VAI tractor - Answer-img_20200120_121605.jpg   Case VAI tractor - Answer-img_20200120_121616.jpg   Case VAI tractor - Answer-img_20200120_121634.jpg  
__________________
In dry dock: ? In factory: CWS T-1. In hanger: Fokker triplanes? under construction: ?
Reply With Quote
Google Adsense
  #16  
Old 01-21-2020, 07:48 PM
whulsey's Avatar
whulsey whulsey is offline
Member
 
Join Date: Jun 2007
Location: Miami, AZ
Posts: 8,839
Total Downloaded: 65.34 MB
Looks goods. Need to get one which I'm sure I can overcomplicate (see long suffering Ursus tractor thread).
Reply With Quote
  #17  
Old 01-21-2020, 08:36 PM
Don Boose's Avatar
Don Boose Don Boose is offline
Member
 
Join Date: Jul 2007
Location: Carlisle, Pennsylvania
Posts: 20,702
Total Downloaded: 424.90 MB
Another great build, Greg. And another model made for the Paper Modelers at Army Heritage Days. If and when.

Don
Reply With Quote
  #18  
Old 01-21-2020, 11:59 PM
jaffro's Avatar
jaffro jaffro is offline
Member
 
Join Date: Jul 2009
Location: Melbourne, Australia.
Posts: 1,102
Total Downloaded: 195.36 MB
Turned out really nice this one... Those tyre treads look like they would've been fun to make...
__________________
Recently Completed: Modelik Scud

Currently Building: Angraf M1070/M1000
Reply With Quote
  #19  
Old 01-22-2020, 07:04 AM
eatcrow2's Avatar
eatcrow2 eatcrow2 is offline
Member
 
Join Date: Jul 2007
Location: Santa Monica, CA
Posts: 2,590
Total Downloaded: 2.23 GB
Great photos showing the process of an outstanding build!
Reply With Quote
  #20  
Old 01-22-2020, 11:45 AM
KCStephens's Avatar
KCStephens KCStephens is offline
Member
 
Join Date: Dec 2007
Location: York, Pennsylvania
Posts: 2,252
Total Downloaded: 678.6 KB
Nicely done!
She'll look great parked beside your Lanz bulldog.
Reply With Quote
Google Adsense
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -6. The time now is 01:21 AM.


Powered by vBulletin®
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.

Parts of this site powered by vBulletin Mods & Addons from DragonByte Technologies Ltd. (Details)
Copyright © 2007-2023, PaperModelers.com