#111
|
||||
|
||||
Thank you guys.
The designer did a good job. Only minor fit up needed. Isaac
__________________
My gallery [http://www.papermodelers.com/gallery...v-r-6&cat=500] Recent buildsMeteor F1, Meteor F8, Mig-Ye8, NA Sabre, A-4E Skyhawk,Mig-15 red, Mig-17 repaint |
#112
|
||||
|
||||
Status so far
__________________
My gallery [http://www.papermodelers.com/gallery...v-r-6&cat=500] Recent buildsMeteor F1, Meteor F8, Mig-Ye8, NA Sabre, A-4E Skyhawk,Mig-15 red, Mig-17 repaint |
#113
|
||||
|
||||
Outstanding work, Isaac! I am still fumbling with the tail section.
Don |
#114
|
||||
|
||||
Quote:
Isaac
__________________
My gallery [http://www.papermodelers.com/gallery...v-r-6&cat=500] Recent buildsMeteor F1, Meteor F8, Mig-Ye8, NA Sabre, A-4E Skyhawk,Mig-15 red, Mig-17 repaint |
#115
|
||||
|
||||
Wing frames
Here are the parts that make the wing frames.
However, as I present it here, I will provide a bit later info on making modifications for the inclusion of separate flaps. Center spar shown in place but not glued The frame segments and put together now dry fit to the fuselage and the wing frames next to the fuselage Isaac
__________________
My gallery [http://www.papermodelers.com/gallery...v-r-6&cat=500] Recent buildsMeteor F1, Meteor F8, Mig-Ye8, NA Sabre, A-4E Skyhawk,Mig-15 red, Mig-17 repaint |
Google Adsense |
#116
|
||||
|
||||
Looking forward to the posting on separate flaps. Nice work Isaac.
Gary
__________________
"Fast is fine, but accuracy is everything" - Wyatt Earp Design Group Alpha https://ecardmodels.com/vendors/design-group-alpha |
#117
|
|||
|
|||
Looks great. Nice clean build.
|
#118
|
||||
|
||||
Wings- Skins and surface- part 1
The kit contains two sets of wings. One for landing gear down and another for clean configurations. The reality is that you can use either one if you plan a gear down version.
So here are the parts. I selected the version with the cutout and save the other wing set for instructional purposes. also I decided to drop the flaps. So here is the wing with the flaps cut out. Lower surface is wider than the upper one, so need to add parts later on. Note that there is an inboard leading edge extension. The glue tab is applied first to the wing. round the leading edge and glue the trailing edge of the ailerons. Also, glue the flaps along the trailing edge, but that is not all done yet. Dry fit with the frame. Note that the frame will need to have parts trimmed off. Cut out the area of the landing gear bay. However, remove the yellow tabs as those are useless and will be hard to use. Just cut the bay area. That's all. Now glue the inboard leading edge extension. More work needed. Isaac
__________________
My gallery [http://www.papermodelers.com/gallery...v-r-6&cat=500] Recent buildsMeteor F1, Meteor F8, Mig-Ye8, NA Sabre, A-4E Skyhawk,Mig-15 red, Mig-17 repaint |
#119
|
||||
|
||||
Main gear bay
I added card material all around the sides of the bay flush with the mating side to the wing interior. This way you can eliminate the tab the kit provides for a better fit.
Glue in place and that is all. Isaac
__________________
My gallery [http://www.papermodelers.com/gallery...v-r-6&cat=500] Recent buildsMeteor F1, Meteor F8, Mig-Ye8, NA Sabre, A-4E Skyhawk,Mig-15 red, Mig-17 repaint |
#120
|
||||
|
||||
Very nice work Isaac. The wing looks great.
Gary
__________________
"Fast is fine, but accuracy is everything" - Wyatt Earp Design Group Alpha https://ecardmodels.com/vendors/design-group-alpha |
Google Adsense |
|
|