#21
|
|||
|
|||
Quote:
Thanks, Gene K |
#22
|
||||
|
||||
Quote:
Maybe others can weigh in. Also, the paper I have is A4 size which is suitable to this model without any modifications. Isaac
__________________
My gallery [http://www.papermodelers.com/gallery...v-r-6&cat=500] Recent buildsMeteor F1, Meteor F8, Mig-Ye8, NA Sabre, A-4E Skyhawk,Mig-15 red, Mig-17 repaint |
#23
|
||||
|
||||
exhaust nozzle
Exhaust nozzle consist of an inner and outer barrel, rear frame with the afterburner ring rendered and 2 side shield for the 2D exhaust halves. In addition there is an assisting frame used to maintain a round shape when applying the super glue close to the lip.
the parts Super glue applied combine the barrels add the side shields when done, re insert the shaper frame to just keep it round. No glue at this point. Technical note: engine thrust can be controlled and optimized when the nozzle area is controlled at different afterburner condition. Most engines have multiple petals; the entire afterburner nozzle is able to open and close as required. The early french engines used on the Super Mystere and early Mirage 3 had a 2 piece nozzle halves that were simple, however, not efficient. Isaac
__________________
My gallery [http://www.papermodelers.com/gallery...v-r-6&cat=500] Recent buildsMeteor F1, Meteor F8, Mig-Ye8, NA Sabre, A-4E Skyhawk,Mig-15 red, Mig-17 repaint |
#24
|
|||
|
|||
Quote:
Gene K |
#25
|
|||
|
|||
Isaac, Always enjoy your stuff, though I don't have the time to say so very often. I have found that with my old iMac and hp920c when the JPEG is displayed I have to fit to page to get the whole sheet. Then I change that page to PDF. When I print that page The 1cm square at the upper left of the page is 0.9cm which is 1/33.33333. I think this will print on letter size paper. So far this has worked on each page, no difference using fit to page in my system.
I used to be able to get a high quality A4 paper imported from Japan to California called Deleter Comic Book Paper, used for drawing Manga stuff with ink. I'm not sure what the weight is, but it sure takes to my old hp920c very well. The printing is beautiful. That old printer doesn't have the ability to print without margins, so sometimes with A4 or letter I tape ,using that thin painter's tape, another sheet to the back a few inches above the paper I'm printing on. That fools the printer as to where the top is, and it prints all the way to the end. I now have a new 2916 Mac and new hp 7612 that has all that stuff, but the ink cartridges run out a lot faster. I guess I'll just have to get used to it. Cheers, Bob |
Google Adsense |
#26
|
|||
|
|||
That's a 2016 Mac of course not 2916! Don't know what that would even mean, would anyone even have paper then? Or would we still be around! It's only 900 years.
Cheers , Bob |
#27
|
||||
|
||||
Not only a good start Isaac but a very clean and quick build so far!
__________________
Cheers from germany, Chris Currently building: Colonial Viper from Uhu02 Finished:Yoav Hozmis Kfir |
#28
|
|||
|
|||
Quote:
Hope it prints as well as Isaac's ... unfortunately I know it won't build as well as Isaac's. Gene K |
#29
|
||||
|
||||
Quote:
Isaac
__________________
My gallery [http://www.papermodelers.com/gallery...v-r-6&cat=500] Recent buildsMeteor F1, Meteor F8, Mig-Ye8, NA Sabre, A-4E Skyhawk,Mig-15 red, Mig-17 repaint |
#30
|
||||
|
||||
Aft fuselage
At this point, I am going to the back.
The aft fuselage sections are simple and elegant once the two most aft sections are joined, add the internal frame. It shapes the fuselage and support the afterburner duct Now add the section forward joined at the star of David roundel. fuzzy picture joined notice the cutout for the speed brakes. Those will be added before going any further forward ( otherwise, there will be no easy access ). here is the AB duct and installed in the rear Isaac
__________________
My gallery [http://www.papermodelers.com/gallery...v-r-6&cat=500] Recent buildsMeteor F1, Meteor F8, Mig-Ye8, NA Sabre, A-4E Skyhawk,Mig-15 red, Mig-17 repaint |
Google Adsense |
|
|