#51
|
||||
|
||||
Quote:
Isaac
__________________
My gallery [http://www.papermodelers.com/gallery...v-r-6&cat=500] Recent buildsMeteor F1, Meteor F8, Mig-Ye8, NA Sabre, A-4E Skyhawk,Mig-15 red, Mig-17 repaint |
#52
|
||||
|
||||
Side intakes
The side intakes were pre assembled and then glued on as a unit to the fuselage as well as the side boundary layer separator.
main parts assembled attach the boundary layer separator strip ready and attached. Same on the other side Isaac
__________________
My gallery [http://www.papermodelers.com/gallery...v-r-6&cat=500] Recent buildsMeteor F1, Meteor F8, Mig-Ye8, NA Sabre, A-4E Skyhawk,Mig-15 red, Mig-17 repaint |
#53
|
||||
|
||||
Well done Isaac. I remember the canopy because of the fairing was a bit of a tricky part, but the fit to the fuselage is excellent and the small strips you still have to add mask any irregularities.
Cheers, Erik |
#54
|
|||
|
|||
hi Isaac
Did you use the black inner frame for the entire circumference of the canopy? YOAV |
#55
|
||||
|
||||
Quote:
Isaac
__________________
My gallery [http://www.papermodelers.com/gallery...v-r-6&cat=500] Recent buildsMeteor F1, Meteor F8, Mig-Ye8, NA Sabre, A-4E Skyhawk,Mig-15 red, Mig-17 repaint |
Google Adsense |
#56
|
|||
|
|||
I asked this question, because it seems to me that the thickness of the lower frame of the canopy looks very thick and protruding from the model body.
I think we talked about this subject not so long ago.... Although I provide the black inner frame of the canopy, I recommend using it only when building the model with an open canopy. When I build the model with a closed canopy, I do not use the black inner frame. I simply paint with black the inside of the main frame and thus prevent the frame from being too thick, and so it is less prominent than the body of the model on which it sits. Shabat Shalom YOAV |
#57
|
|||
|
|||
looking great!
|
#58
|
||||
|
||||
Quote:
Yes we discussed this in the past. I'm not at home now and don't recall if I used the inner parts on the sides. I hope I did not I added the small outside strips and it appears better . Isaac
__________________
My gallery [http://www.papermodelers.com/gallery...v-r-6&cat=500] Recent buildsMeteor F1, Meteor F8, Mig-Ye8, NA Sabre, A-4E Skyhawk,Mig-15 red, Mig-17 repaint |
#59
|
||||
|
||||
Canopy side strips
There are four thin strips that glue on either side of the canopy. I applied them from back to front and that turned out to be an error as it did not line up with the windshield forward frame. The correct way was to start at the forward edge!
However, it is too late to remove and re position and I decided to leave it as is. Minor error Isaac
__________________
My gallery [http://www.papermodelers.com/gallery...v-r-6&cat=500] Recent buildsMeteor F1, Meteor F8, Mig-Ye8, NA Sabre, A-4E Skyhawk,Mig-15 red, Mig-17 repaint |
#60
|
||||
|
||||
Vertical fin
Here are the kit frames
I added extra strips to the sides to smooth the external surfaces Here are the tail fin parts dry fit first and glued in place. Isaac
__________________
My gallery [http://www.papermodelers.com/gallery...v-r-6&cat=500] Recent buildsMeteor F1, Meteor F8, Mig-Ye8, NA Sabre, A-4E Skyhawk,Mig-15 red, Mig-17 repaint |
Google Adsense |
|
|