PaperModelers.com

Go Back   PaperModelers.com > > >

Reply
 
Thread Tools Display Modes
  #11  
Old 02-03-2019, 04:07 AM
Kevin WS's Avatar
Kevin WS Kevin WS is offline
Member
 
Join Date: Aug 2010
Location: South Africa.
Posts: 4,978
Total Downloaded: 354.01 MB
Go for it.

I cannot believe you are able to model so much! Wish I could!
__________________
The SD40 is 52 now!
Reply With Quote
  #12  
Old 02-08-2019, 11:16 PM
Styrian Spitfire's Avatar
Styrian Spitfire Styrian Spitfire is offline
Member
 
Join Date: Feb 2014
Location: Styria
Posts: 715
Total Downloaded: 0
Hello Kevin !

Oh it is not so difficult , you only must take one hour per day

and now I built further .

ATTENTION ! It is important to loosely fit the rings 1b + 1c BEFORE glueing the parts ... also note that the longitudinal straps of part 2 are at the bottom and those from part 3 at the top

Now I put the ten longitudinal straps first, without gluing them ... while one frame after the other is glued, I start during the dry phases with the outer trunk parts.

The ultrafine ring 1a ... is glued on the front

Yours sincerely

Kurt
Attached Thumbnails
Caproni Stipa - Orlik - 1:33-dscf0045.jpg   Caproni Stipa - Orlik - 1:33-dscf0046.jpg   Caproni Stipa - Orlik - 1:33-dscf0047.jpg   Caproni Stipa - Orlik - 1:33-dscf0001.jpg   Caproni Stipa - Orlik - 1:33-dscf0002.jpg  

Caproni Stipa - Orlik - 1:33-dscf0003.jpg  
Reply With Quote
  #13  
Old 02-09-2019, 10:34 PM
Styrian Spitfire's Avatar
Styrian Spitfire Styrian Spitfire is offline
Member
 
Join Date: Feb 2014
Location: Styria
Posts: 715
Total Downloaded: 0


The fuselage parts are prepared ... do not attach the front and rear ring yet

Now push the cylinder over the frames ... the only splices are just front and back

Yours sincerely
Kurt
Attached Thumbnails
Caproni Stipa - Orlik - 1:33-dscf0004.jpg   Caproni Stipa - Orlik - 1:33-dscf0005.jpg   Caproni Stipa - Orlik - 1:33-dscf0046-2-.jpg   Caproni Stipa - Orlik - 1:33-dscf0047-2-.jpg  
Reply With Quote
  #14  
Old Yesterday, 12:44 PM
Styrian Spitfire's Avatar
Styrian Spitfire Styrian Spitfire is offline
Member
 
Join Date: Feb 2014
Location: Styria
Posts: 715
Total Downloaded: 0
Now insert the wing spar, cut the tabs slightly ... and the front ring ...
... glue, contrary to all fears, the whole thing has not been so bad ... now the back ring ...
... still glue - hull finished !! The fit is excellent.
The two cylinders are only glued to the front and rear, there is no glue on the longitudinal frames, but it is still very stable.

Yours sincerely
Kurt
Attached Thumbnails
Caproni Stipa - Orlik - 1:33-dscf0048.jpg   Caproni Stipa - Orlik - 1:33-dscf0049.jpg   Caproni Stipa - Orlik - 1:33-dscf0050.jpg   Caproni Stipa - Orlik - 1:33-dscf0051.jpg   Caproni Stipa - Orlik - 1:33-dscf0052.jpg  

Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -6. The time now is 02:50 PM.


Powered by vBulletin®
Copyright ©2000 - 2019, Jelsoft Enterprises Ltd.
Resources saved on this page: MySQL 66.67% / PHP 89.47%
Parts of this site powered by vBulletin Mods & Addons from DragonByte Technologies Ltd. (Details)
Copyright © 2007-17, Paper Modelers.com