PaperModelers.com

Go Back   PaperModelers.com > > >

Reply
 
Thread Tools Display Modes
  #41  
Old 04-19-2019, 11:31 PM
Styrian Spitfire's Avatar
Styrian Spitfire Styrian Spitfire is offline
Member
 
Join Date: Feb 2014
Location: Styria
Posts: 755
Total Downloaded: 0
Now the parts 43 for the engine fairing ... I start with 43 a, b, c.
In part 43 a, each strip is individually glued ... with the bars, the engine is now finished
The exhaust is actually made of wire, but I make this out of 1.5 mm Finn cardboard

Yours sincerely
Kurt
Attached Thumbnails
Caproni Stipa - Orlik - 1:33-dscf0068.jpg   Caproni Stipa - Orlik - 1:33-dscf0069.jpg   Caproni Stipa - Orlik - 1:33-dscf0070.jpg   Caproni Stipa - Orlik - 1:33-dscf0001.jpg   Caproni Stipa - Orlik - 1:33-dscf0002.jpg  

Reply With Quote
  #42  
Old 04-21-2019, 11:17 PM
Styrian Spitfire's Avatar
Styrian Spitfire Styrian Spitfire is offline
Member
 
Join Date: Feb 2014
Location: Styria
Posts: 755
Total Downloaded: 0
With the two wing spars the engine is suspended in the tube. First sample, fits very well!
The support elements for the motor are reinforced inside with wire.

First, I will attach the breakpoints for the columns.
The engine, the struts and the "tension wires" prepared. Now it gets really exciting - the installation of the engine ....

Yours sincerely
Kurt
Attached Thumbnails
Caproni Stipa - Orlik - 1:33-dscf0003.jpg   Caproni Stipa - Orlik - 1:33-dscf0004.jpg   Caproni Stipa - Orlik - 1:33-dscf0005.jpg   Caproni Stipa - Orlik - 1:33-dscf0006.jpg  
Reply With Quote
  #43  
Old 04-22-2019, 06:41 AM
ricleite ricleite is offline
Member
 
Join Date: Jun 2009
Posts: 1,190
Total Downloaded: 0
There is rigging between the engine and the duct?! The accessibility for assembly looks problematic...
Reply With Quote
  #44  
Old 05-08-2019, 10:05 AM
Styrian Spitfire's Avatar
Styrian Spitfire Styrian Spitfire is offline
Member
 
Join Date: Feb 2014
Location: Styria
Posts: 755
Total Downloaded: 0
Hello Ricardo ,
You'll see it's not as difficult as it looks before

But now in it ...

First thread the tension wires and secure them with clamps ... through the tensioned wires the motor centers itself in the tube

Now tighten the wing spars and wires on the outside ... the support struts are glued, the outer ring I have the edge now blue colored

Yours sincerely
Kurt
Attached Thumbnails
Caproni Stipa - Orlik - 1:33-dscf0007.jpg   Caproni Stipa - Orlik - 1:33-dscf0008.jpg   Caproni Stipa - Orlik - 1:33-dscf0009.jpg   Caproni Stipa - Orlik - 1:33-dscf0010.jpg  
Reply With Quote
  #45  
Old 05-08-2019, 02:06 PM
Don Boose's Avatar
Don Boose Don Boose is offline
Member
 
Join Date: Jul 2007
Location: Carlisle, Pennsylvania
Posts: 16,692
Total Downloaded: 120.19 MB
Outstanding work!

Don
Reply With Quote
Login to remove ads
  #46  
Old 05-08-2019, 02:35 PM
Isaac's Avatar
Isaac Isaac is offline
Member
 
Join Date: Oct 2010
Location: Dayton Ohio
Posts: 5,959
Total Downloaded: 81.10 MB
Nice work on the rigging


Isaac
__________________
My gallery [http://www.papermodelers.com/gallery...v-r-6&cat=500]
Recent buildsMig-15UTI, Su-9(1st), Ouragan, Kfir-C7, Mirage 3C, F-84F, F-104G, Mystere 4A
Reply With Quote
  #47  
Old 05-09-2019, 04:38 AM
Erik Zwaan's Avatar
Erik Zwaan Erik Zwaan is offline
Member
 
Join Date: Sep 2012
Location: Leiden area, The Netherlands
Posts: 1,666
Total Downloaded: 17.13 MB
Amazing work Kurt!

Erik
Reply With Quote
  #48  
Old 05-11-2019, 04:23 PM
smithdr smithdr is offline
Member
 
Join Date: Jul 2016
Location: Federal Way, Washington
Posts: 721
Total Downloaded: 146.69 MB
Neat job! Well done...I've been following this one for awhile.


Very precise.


Dan
Reply With Quote
  #49  
Old 05-15-2019, 10:56 AM
Styrian Spitfire's Avatar
Styrian Spitfire Styrian Spitfire is offline
Member
 
Join Date: Feb 2014
Location: Styria
Posts: 755
Total Downloaded: 0
Hello Friends off Stipa

Thank you all for the nice comments

Now scene change, the wings follow ...

Step by step, now the wings are glued, but not with the wing spars ... after everything is well dried I can do the wing
Remove the skeleton from the bars.

The wings leading edges must be rounded well before ... on the ribs I paste thin strips of paper

Yours sincerely
Kurt
Attached Thumbnails
Caproni Stipa - Orlik - 1:33-dscf0001.jpg   Caproni Stipa - Orlik - 1:33-dscf0002.jpg   Caproni Stipa - Orlik - 1:33-dscf0006.jpg   Caproni Stipa - Orlik - 1:33-dscf0007-2-.jpg  
Reply With Quote
  #50  
Old 05-16-2019, 06:12 AM
Erik Zwaan's Avatar
Erik Zwaan Erik Zwaan is offline
Member
 
Join Date: Sep 2012
Location: Leiden area, The Netherlands
Posts: 1,666
Total Downloaded: 17.13 MB
Curiously awaiting how the outcome of the wing section will be....

Erik
Reply With Quote
Login to remove ads
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -6. The time now is 11:21 AM.


Powered by vBulletin®
Copyright ©2000 - 2019, Jelsoft Enterprises Ltd.
Resources saved on this page: MySQL 8.70%
Parts of this site powered by vBulletin Mods & Addons from DragonByte Technologies Ltd. (Details)
Copyright © 2007-17, Paper Modelers.com