PaperModelers.com

Go Back   PaperModelers.com > > >

Reply
 
Thread Tools Display Modes
  #11  
Old 02-07-2019, 01:25 PM
Richschindler Richschindler is offline
Member
 
Join Date: Jun 2014
Location: No longer living in NYC. Mooresville, NC is my home now.
Posts: 2,324
Total Downloaded: 2.34 GB
Looks great!!!!
Reply With Quote
  #12  
Old 02-07-2019, 03:37 PM
Rata's Avatar
Rata Rata is offline
Member
 
Join Date: Mar 2018
Location: Sydney, Australia
Posts: 2,832
Total Downloaded: 655.31 MB
Thanks for the encouragement folks. Will keep going on her and have it available ASAP.
__________________
''Oh, stop whining! Can't you just print off another one?''- my wife ca 2018
Reply With Quote
  #13  
Old 02-07-2019, 07:03 PM
Brent Brent is offline
Member
 
Join Date: Jul 2007
Location: Abbotsford, BC, Canada
Posts: 357
Total Downloaded: 268.98 MB
Good job Garry, great repaint and build.

Brent
Reply With Quote
  #14  
Old 02-07-2019, 07:16 PM
Vinalssergio155's Avatar
Vinalssergio155 Vinalssergio155 is offline
Member
 
Join Date: Jan 2018
Location: Ezeiza.Argentina
Posts: 1,948
Total Downloaded: 202.96 MB
It looks great Garry.
Reply With Quote
  #15  
Old 02-08-2019, 06:29 AM
Rata's Avatar
Rata Rata is offline
Member
 
Join Date: Mar 2018
Location: Sydney, Australia
Posts: 2,832
Total Downloaded: 655.31 MB
Thanks Brent & Sergio.
Did the rear part of the first engine pod today. Checks out so I'll use it as a pattern for the other three. Also I spoke to Chatchai today about the three horizontal lines on each side of the nosecone (see pic). These are fine on the grey versions but a bit too prominent on this one. He agrees so I've removed them for the final draft.
Attached Thumbnails
ThaiPaperworks B-52H Repaint-img_9143.jpg  
__________________
''Oh, stop whining! Can't you just print off another one?''- my wife ca 2018
Reply With Quote
Login to remove ads
  #16  
Old 02-08-2019, 07:17 AM
CMDRTED's Avatar
CMDRTED CMDRTED is offline
Member
 
Join Date: Oct 2007
Location: Avondale,Pa.
Posts: 1,879
Total Downloaded: 418.86 MB
not only a great recolor but a very clean build Gary, very impressive!
Reply With Quote
  #17  
Old 02-08-2019, 04:01 PM
Rata's Avatar
Rata Rata is offline
Member
 
Join Date: Mar 2018
Location: Sydney, Australia
Posts: 2,832
Total Downloaded: 655.31 MB
Cheers CMDR.
Port wing finished and starboard about 50%. When all the engine pods are done I'll print and test build the rest. I've found when recolouring the worst offender for colour misalignment is always the fuselage but as that's all ok I can't see the rest of the test build presenting any problems.
Note to self: print off the rest of it in one hit. If you look hard at the pics you'll notice slight colour variations on the fin and starboard tailplane. Done on the same laser printer as the rest of plane but on different days. Cautionary tale!
__________________
''Oh, stop whining! Can't you just print off another one?''- my wife ca 2018
Reply With Quote
  #18  
Old 02-08-2019, 04:19 PM
Texman's Avatar
Texman Texman is offline
Lilliput Transportation Mod
 
Join Date: Jul 2007
Posts: 5,861
Total Downloaded: 1,023.11 MB
Quote:
Originally Posted by Rata View Post
Note to self: print off the rest of it in one hit. If you look hard at the pics you'll notice slight colour variations on the fin and starboard tailplane. Done on the same laser printer as the rest of plane but on different days. Cautionary tale!

Exactly! When I do layering/detailing, I print both copies at the same time for
that reason. You can print the same file with the same settings, on different days,
and they will be different. Not much, but it is usually noticeable.
__________________
Ray

Respect the Paper, RESPECT IT!
I don't always listen to Bob Seger but when I do, so do the neighbors.....
Reply With Quote
  #19  
Old 02-08-2019, 04:21 PM
Texman's Avatar
Texman Texman is offline
Lilliput Transportation Mod
 
Join Date: Jul 2007
Posts: 5,861
Total Downloaded: 1,023.11 MB
I noticed on your engine fan sections, the tabs are visible.
Are there intake liners in the kit to cover them?
__________________
Ray

Respect the Paper, RESPECT IT!
I don't always listen to Bob Seger but when I do, so do the neighbors.....
Reply With Quote
  #20  
Old 02-08-2019, 06:36 PM
Rata's Avatar
Rata Rata is offline
Member
 
Join Date: Mar 2018
Location: Sydney, Australia
Posts: 2,832
Total Downloaded: 655.31 MB
Sorry Ray, no liners on either the intake or tailpipe are provided. The builder will have to do some modelling (eek! ) and color themselves. Bear in mind this will be even more pronounced on the grey versions.
__________________
''Oh, stop whining! Can't you just print off another one?''- my wife ca 2018
Reply With Quote
Login to remove ads
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -6. The time now is 12:10 AM.


Powered by vBulletin®
Copyright ©2000 - 2019, Jelsoft Enterprises Ltd.
Resources saved on this page: MySQL 8.70%
Parts of this site powered by vBulletin Mods & Addons from DragonByte Technologies Ltd. (Details)
Copyright © 2007-17, Paper Modelers.com