#1
|
||||
|
||||
Why holes in formers?
I've built pretty much FG models because I like them and I think they suit my abilities.
Since I joined this group I see many models, almost all aircraft, that are constructed using 'formers', kind of like bulkhead structures, many with holes of various sizes cut through them. I've followed a couple of build threads and it appears that the main use for these holes is that they make a convenient grip. I've seen some builders route their rigging through them. Is there any other use for these holes? Anything else I'm missing here? If I build a model with these formers and I don't cut the holes is that a problem? Thanks, SFX |
Google Adsense |
#2
|
||||
|
||||
check this link Holes in aviation frames?
__________________
"Rock is Dead, Long Live Paper and Scissors" International Paper Model Convention Blog http://paperdakar.blogspot.com/ "The weak point of the modern car is the squidgy organic bit behind the wheel." Jeremy Clarkson, Top Gear's Race to Oslo |
#3
|
||||
|
||||
SFX,
Not sure about the other designers, but weight reduction for flight, in my models. Mike |
#4
|
||||
|
||||
No problem but makes life harder...
The holes are there for three reasons: To stick your finger in to manouevre the former in the skin tube. To let to reach in with small fingers and tools to burnish the inside of a join. To reduce weight in some more delicate models...
__________________
Please critique my posts honestly i.e. say what you think so I can learn and improve... The World According to Me |
#5
|
||||
|
||||
Swampfox,
These holes are primarily called finger holes. They aid in installing the former into it's location in the fuselage section. You do not have to cut them out. However they do need to be removed if say they are just behind the area where the prop wire or prop rotation dowel would interfere due to it's length. They also give access to the inside area of the fuselage section. Ron |
Google Adsense |
#6
|
||||
|
||||
The guys tell you right... if you have a former that is one that has NO cut-out {some don't - depends on structure} i usually glue a few extra tabs to the flat surface so that i can use tweezers on them to PULL the former into place - when dry, cut them off again.
|
#7
|
||||
|
||||
Holes in formers are great for larger scale aircraft - 1/33rd etc. But in small scales their use is limited. In my 1/72 builds that make use of formers, I just cut a slit to accept a screwdriver, and install/manipulate the former as needed by twisting the screwdriver. I first saw this technique on this forum - maybe one of goldenbear's aircraft build threads? Anyway, it works very well for small scale models.
__________________
Regards, Don I don't always build models, but when I do... I prefer paper. Keep your scissors sharp, my friends. |
#8
|
||||
|
||||
Quote:
Quote:
Cheers Jim |
#9
|
||||
|
||||
Making things clear, this is needed most when there are spanwise formers only and are installed AFTER the skin is formed into a cone. With intersecting formers in both lengthwise and spanwise directions the skin is usually applied last so holes are not found on this type of design.
__________________
"The world is big" On hold: Fuyuzuki, Zao, Zara, Akizuki, Past works: XP55 Ascender, CA Ibuki, Seafang F32, IS-3, Spitfire V, J-20 |
#10
|
||||
|
||||
Good for 'drying' too
Not to be discounted is the effect of 'airflow' to both sides of the seam. I like the holes because it allows me to reach in with the ol' burnishing tool and press the seams from inside while supporting from the outside. Plus, I can often re-establish my pre-formed 'compound curvature' which tends to flatten out when applying the skin to the former (I know, that is "backwards" from the usual practice.)
__________________
Regards, Robert In Work: Uhu02 Tinkerbell - [under Tapcho's thread] Tinkerbell - a fairy with an attitude Nobi Junkers SRF BETA build - BETA Build: Nobi's Junkers SRF 1:48 scale |
Google Adsense |
|
|