PaperModelers.com

Go Back   PaperModelers.com > Card Models > Model Builds > PASA, Paper Aeronautical and Space Administration

Reply
 
Thread Tools Display Modes
  #1  
Old 12-27-2017, 02:56 AM
dhanners's Avatar
dhanners dhanners is offline
Member
 
Join Date: Jul 2007
Location: Manchester, UK
Posts: 2,599
Total Downloaded: 1.59 GB
The original X-15-2, 66671....

I’ll post some “beauty” shots later, but here’s my latest....

After finishing Ken West’s great X-15A-2, I became convinced that, despite his claims to the contrary, his model could be converted into the shorter, original X-15. It was just a matter of what you cut and where you cut it. So here is X-15 No. 2, 66671, in its pre-stretch configuration, in 1/48th scale. (Ken’s model comes at 1/32nd scale, but I shrunk it.)

The major change involved cutting a 28-scale-inch chunk out of the fuselage, as well as a similar length from the chines. The challenging part is you have to trim the chines in a different location than the fuselage. I shortened the fuselage by cutting off 1.5cm of Part 3, where the fuselage was extended to house a liquid hydrogen tank on the real ‘A-2. Fortunately, Ken’s piece has a panel line near there. Once the entire fuselage was assembled and dry, I assembled (but didn’t install) the six forward pieces of each chine. I cut the rear chine pieces at the panel aft of the “U.S. AIR FORCE” legend, shaped and assembled those pieces and glued them to the forward chine assemblies. Those assemblies were then glued to the fuselage.

The rear chines each come in three pieces -- top, middle and bottom. The top piece carries the lower half of the national insignia, which has to line up with the top half of the insignia on the fuselage. I lined up the markings and that told me where to cut the piece to meet up with the forward chine assembly. While I had the piece lined up, I also determined where I had to cut to remove the rear chine extensions. This newly trimmed top chine piece told me how much I had to cut from the middle and bottom chine sections. I did this for each side. Once that was done, I shaped the chine pieces and glued them together. They were then glued onto the fuselage, joining up with the forward chine sections. I fashioned a new end piece for each chine from black card.

I wanted to model 66671 as it appeared in the summer of 1962, before the November hard landing that led to its conversion to the ‘A-2. X-15 markings varied widely from mission to mission and vehicle to vehicle. References are a must. On the fuselage, the “U.S. AIR FORCE” legend could appear in different places, as could the national insignia. On the dorsal stabilizer, the yellow NASA band could be on both sides of the rudder or just one side or not at all. Similarly, some flights had the serial number on both sides of the fixed portion of the dorsal stabilizer, while others just had it on one side. Still others carried the serial number on the rudder; it could be on one side or both. Like the NASA tail band, the font of the serial numbers also could differ from flight to flight. The wings could carry both the national insignia (left wing) and USAF (right) or just the national insignia -- or no markings at all.

In the summer of ‘62, 66671 had the yellow NASA band on the left side of the dorsal stabilizer but not the right, and it carried the serial number on the right but not the left. The wings carried no markings, except for the white “Beware of Blast” warning on the right wing only.

I modeled the tail markings by cutting apart Ken’s pieces, adding some of the pieces from the “in-flight version,” and mixing and matching pieces and assembling them into the tail. I also improved the accuracy of the model by splitting the dorsal stabilizer into two sections -- the fixed portion and the rudder. Ken models the dorsal stabilizer all as one piece. On the real vehicle, there is a gap between the fixed and moving sections; you can see daylight between them. For this model, the wing markings were removed electronically.

A list of my additions/modifications/corrections, from fore to aft:
-- The fuselage nose piece immediately behind the Q ball was replaced with black card, using the kit piece as a template;
-- Cockpit windows were changed from ovals to the proper pre-stretch shape;
-- The kit piece for the section immediately aft of the cockpit was replaced with black card, using the kit piece as a template;
-- Bug-eye camera housings were scratchbuilt, and cameras added;
-- The liquid oxygen vent on the top of the fuselage was detailed;
-- Replaced the various kit drains with smaller, more accurate ones made from wire coating;
-- The fuselage was shortened 28 scale inches;
-- The chines were shortened 28 scale inches;
-- Strenghthening strips were added to the wing-fuselage joint, as on the real vehicle;
-- A gap was added to replicate the gap between the fuselage and wings forward of the first panel line on the wing, as on the real vehicle;
-- The fixed and moving sections of the dorsal and ventral stabilizers were split and a pivot added to replicate the gap between the two;
-- Plumbing on the back of the rudder was replicated with wire;
-- The horizontal stabilizers were altered to reflect the accurate cross section;
-- Pivot points were added to the horizontal stabilizers to replicate the fuselage-stabilizer gap seen on the real vehicle;
-- A new engine rear section was built from black card, using the kit part as a template;
-- The end piece of the rear engine section was inset to improve accuracy;
-- The chine extensions at the rear were removed and new end pieces were made from black card;
-- The shape of the stowed landing skids was altered to more accurately reflect those on the vehicle;
-- Silver card was used to model the exterior housing of the XLR-99 rocket motor, using the kit parts as templates;
-- Replaced the parachute cover on the section of the tail jettisoned before landing;

I need to thank Ken West for designing a great model. John Bowden also helped out. Research on markings by Jeffrey Kubiak of Hypersonic Models was invaluable. It feels good to finally add this important research vehicle to the collection....
Attached Thumbnails
The original X-15-2, 66671....-img_6233.jpg   The original X-15-2, 66671....-img_6237.jpg   The original X-15-2, 66671....-img_6239.jpg   The original X-15-2, 66671....-img_6241.jpg   The original X-15-2, 66671....-img_6236.jpg  

The original X-15-2, 66671....-img_6247.jpg  
Reply With Quote
Google Adsense
  #2  
Old 12-27-2017, 03:22 AM
southwestforests's Avatar
southwestforests southwestforests is offline
Member
 
Join Date: Feb 2011
Location: On the edge of the river valley
Posts: 1,474
Total Downloaded: 5.88 MB
Good looking models of a good looking plane. Even though having liked X-15 for as long as can be remembered and having, and having read and re-read, several books about it I wouldn't be able to tell all those details and differences.
Over the weekend re-read Milton Thompson's book At the Edge of Space.
__________________
Screw the rivets, I'm building for atmosphere, not detail.
later, F Scott W
Reply With Quote
  #3  
Old 12-27-2017, 05:05 AM
umtutsut's Avatar
umtutsut umtutsut is offline
Member
 
Join Date: Aug 2009
Location: Indianapolis, IN
Posts: 1,485
Total Downloaded: 302.42 MB
Another stunning piece of work, David! Even after 10 years of building card models, I wouldn't consider attempting such a conversion.

Heck, I haven't even gotten up the nerve to attempt the original.

Les (The Voice of Authority)
Reply With Quote
  #4  
Old 12-27-2017, 05:25 AM
MacSongLi's Avatar
MacSongLi MacSongLi is offline
Member
 
Join Date: May 2012
Location: Ontario, Canada
Posts: 5,977
Total Downloaded: 912.66 MB
WOW, amazing work Dave.

Gary
__________________
"Fast is fine, but accuracy is everything" - Wyatt Earp

Design Group Alpha
https://ecardmodels.com/vendors/design-group-alpha
Reply With Quote
  #5  
Old 12-27-2017, 06:14 AM
Rubenandres77's Avatar
Rubenandres77 Rubenandres77 is offline
Moderator
 
Join Date: Aug 2010
Location: Bogota, Colombia
Posts: 2,849
Total Downloaded: 652.45 MB
You made a great job!

Very nice models, and an interesting conversion. What a beauty!

Looking forward for the final photos!
__________________
Rubén Andrés Martínez A.

Reply With Quote
Google Adsense
  #6  
Old 12-27-2017, 07:07 AM
dhanners's Avatar
dhanners dhanners is offline
Member
 
Join Date: Jul 2007
Location: Manchester, UK
Posts: 2,599
Total Downloaded: 1.59 GB
Thanks for the kind words, guys. Here, in theory, are some better photos.

Now all I need is a 1/48th-scale B-52, although I'm out of display space as it is....
Attached Thumbnails
The original X-15-2, 66671....-img_6250.jpg   The original X-15-2, 66671....-img_6251.jpg   The original X-15-2, 66671....-img_6254.jpg   The original X-15-2, 66671....-img_6255.jpg   The original X-15-2, 66671....-img_6256.jpg  

The original X-15-2, 66671....-img_6265.jpg  
Reply With Quote
  #7  
Old 12-27-2017, 07:34 AM
Knife's Avatar
Knife Knife is offline
Member
 
Join Date: Jul 2007
Location: NW Florida
Posts: 2,068
Total Downloaded: 1.89 GB
A great conversion job. Shows the flexibility of paper as a modeling medium. I like that you did both versions. Super job.
Reply With Quote
  #8  
Old 12-27-2017, 08:21 AM
airdave's Avatar
airdave airdave is offline
Member
 
Join Date: Apr 2009
Location: Ontario Canada
Posts: 14,246
Total Downloaded: 257.44 MB
yeah, very nicely built.
__________________
SUPPORT ME PLEASE: PaperModelShop
Or, my models at ecardmodels: Dave'sCardCreations
Reply With Quote
  #9  
Old 12-27-2017, 10:08 AM
dwyaneward dwyaneward is offline
Member
 
Join Date: Mar 2017
Location: Fairview, Texas
Posts: 111
Total Downloaded: 4.67 GB
Awesome job, thanks for sharing
__________________
Dwyane Ward | Fairview, TX
Reply With Quote
  #10  
Old 12-27-2017, 11:50 AM
John Bowden's Avatar
John Bowden John Bowden is offline
Eternal Member
 
Join Date: Jul 2007
Location: Madison, MS USA
Posts: 3,434
Total Downloaded: 223.07 MB
I'm now gathering info and with David's help will work on making 2018 and X-15 year!
__________________
www.dgapapermodels.com

My Drawings
Reply With Quote
Google Adsense
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -6. The time now is 06:18 AM.


Powered by vBulletin®
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.

Parts of this site powered by vBulletin Mods & Addons from DragonByte Technologies Ltd. (Details)
Copyright © 2007-2023, PaperModelers.com