PaperModelers.com

Go Back   PaperModelers.com > Card Models > Model Builds > Ships and watercraft

Reply
 
Thread Tools Display Modes
  #1  
Old 02-07-2012, 10:12 AM
Bluenoser's Avatar
Bluenoser Bluenoser is offline
Member
 
Join Date: Jul 2007
Location: Nova Scotia
Posts: 888
Total Downloaded: 55.56 MB
SS Zuiderkruis

I got this model from Lighthouse when they were still around. I picked this one 'cause my Mom's family emigrated from Holland to Canada on this ship and came right through Peir 21 in Halifax, Nova Scotia, although the journey ended in Edmonton. I now live in Nova Scotia and Peir 21 is a heritage site for many of Canada's immigrants from days gone by. This seemed like a fitting model for my collection.
Attached Thumbnails
SS Zuiderkruis-1.jpg  

Last edited by Bluenoser; 02-07-2012 at 11:03 AM.
Reply With Quote
Google Adsense
  #2  
Old 02-07-2012, 10:31 AM
Bluenoser's Avatar
Bluenoser Bluenoser is offline
Member
 
Join Date: Jul 2007
Location: Nova Scotia
Posts: 888
Total Downloaded: 55.56 MB
I wanted to open the portholes in the ship. I found that a printer ink re-fill syringe did the job quite nicely. A few twists and the hole was open, however I needed to clear the tube after each removal. By keeping the plunger extended I was able the press it and 'blow' the removed porthole from the syringe on most occasions.
Attached Thumbnails
SS Zuiderkruis-2.jpg  
Reply With Quote
  #3  
Old 02-07-2012, 10:37 AM
Bluenoser's Avatar
Bluenoser Bluenoser is offline
Member
 
Join Date: Jul 2007
Location: Nova Scotia
Posts: 888
Total Downloaded: 55.56 MB
The hull skeleton was formed. I inserted a longstrip of wood into the triangular 'keel' to reduce the ship from hogging or sagging after applying the hull plating as a result from glue drying. I have had this happen before so this is just a precautionary move.
Attached Thumbnails
SS Zuiderkruis-3.jpg  
Reply With Quote
  #4  
Old 02-07-2012, 10:41 AM
Bluenoser's Avatar
Bluenoser Bluenoser is offline
Member
 
Join Date: Jul 2007
Location: Nova Scotia
Posts: 888
Total Downloaded: 55.56 MB
I applied some blasa stiffening members in the hull at the location where the hull plates are expected to join. I did this because I figured that I may get some warpage here once I join them and if it was reinforced, I could apply a little more pressure to ensure a tight bond between the parts.
Attached Thumbnails
SS Zuiderkruis-4.jpg  
Reply With Quote
  #5  
Old 02-07-2012, 10:47 AM
Bluenoser's Avatar
Bluenoser Bluenoser is offline
Member
 
Join Date: Jul 2007
Location: Nova Scotia
Posts: 888
Total Downloaded: 55.56 MB
That seemed like such a good idea I extended it several more bays forward and aft. This way I can safely handle the model when building without overflexing the hull sides and revealing all the frames behind it.
The main deck was also applied and the balsa hull stiffeners did well to help out on the deck here.
Also the fore and aft decks were appiled with additional card stiffeners located below each (still visible on the Fore deck).
Attached Thumbnails
SS Zuiderkruis-5.jpg  
Reply With Quote
Google Adsense
  #6  
Old 02-07-2012, 10:50 AM
jagolden01's Avatar
jagolden01 jagolden01 is offline
Member
 
Join Date: Jan 2008
Posts: 2,529
Total Downloaded: 37.84 MB
Very nice start to this.
Reply With Quote
  #7  
Old 02-07-2012, 10:53 AM
Royaloakmin Royaloakmin is offline
Member
 
Join Date: Oct 2007
Location: Windsor ON
Posts: 1,318
Total Downloaded: 31.99 MB
Good luck! Always nice to build something with a family connection.
__________________
Fred Bultman
Reply With Quote
  #8  
Old 02-07-2012, 10:55 AM
Michael Mash's Avatar
Michael Mash Michael Mash is offline
POTM Moderator
 
Join Date: Oct 2008
Location: The Great Lakes
Posts: 5,397
Total Downloaded: 18.36 MB
Good luck with your Zuiderkruis.
It is fun watching a new project and some new techniques.
The syringe for the portholes is quite clever.
Mike
Reply With Quote
  #9  
Old 02-07-2012, 10:59 AM
Bluenoser's Avatar
Bluenoser Bluenoser is offline
Member
 
Join Date: Jul 2007
Location: Nova Scotia
Posts: 888
Total Downloaded: 55.56 MB
Here we can see the portholes and scuppers opened up. The Gray line visible between the scuppers, and above the port holes represents the level of the main deck. Images of the real ship show this as open so I am contemplating on doing this too, however it will make the bulwark loose and flexible.
ss Zuiderkruis
Attached Thumbnails
SS Zuiderkruis-6.jpg  

Last edited by Bluenoser; 02-07-2012 at 11:09 AM.
Reply With Quote
  #10  
Old 02-07-2012, 11:02 AM
Bluenoser's Avatar
Bluenoser Bluenoser is offline
Member
 
Join Date: Jul 2007
Location: Nova Scotia
Posts: 888
Total Downloaded: 55.56 MB
The hull is longer than it needs to be and the extra is identifed on the part. I like that.
Attached Thumbnails
SS Zuiderkruis-7.jpg  
Reply With Quote
Google Adsense
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -6. The time now is 04:09 AM.


Powered by vBulletin®
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.

Parts of this site powered by vBulletin Mods & Addons from DragonByte Technologies Ltd. (Details)
Copyright © 2007-2023, PaperModelers.com