PaperModelers.com

Go Back   PaperModelers.com > Card Models > Model Builds > Ships and watercraft

Reply
 
Thread Tools Display Modes
  #1  
Old 10-25-2015, 01:47 AM
RelloemSualk RelloemSualk is offline
Member
 
Join Date: Aug 2010
Location: Ulm, FRG
Posts: 170
Total Downloaded: 0
Project 1135, frigate Kriwak I class, Oriel, 1:250

Hallo,

Today I'll start a report of my version of the Krival I class frigate named "Dejatielnyj".
The scale was modified to 1:250 (kit is 1:200) and several adaptions were made I'll describe in the course of the thread.
Waterline model is my preferred choice - so the first task is to identify the waterline marker line in the formers of the hull.
The formers were made of Bristolpaper (0.5 mm). The former assembly is straight forward and I added several home made formers (cardboard 1mm) to reenforce the structure (as I always do).
Regards Klaus


Freshly unpacked link
Projekt 1135, frigate Kriwak I class, Oriel, 1:200
Attached Thumbnails
Project 1135, frigate Kriwak I class, Oriel, 1:250-bb_oriel63_000.jpg   Project 1135, frigate Kriwak I class, Oriel, 1:250-bb_oriel63_001.jpg   Project 1135, frigate Kriwak I class, Oriel, 1:250-bb_oriel63_002.jpg   Project 1135, frigate Kriwak I class, Oriel, 1:250-bb_oriel63_003.jpg   Project 1135, frigate Kriwak I class, Oriel, 1:250-bb_oriel63_004.jpg  

Project 1135, frigate Kriwak I class, Oriel, 1:250-bb_oriel63_005.jpg  

Last edited by RelloemSualk; 10-25-2015 at 01:51 AM. Reason: link added
Reply With Quote
Google Adsense
  #2  
Old 10-25-2015, 03:48 AM
RelloemSualk RelloemSualk is offline
Member
 
Join Date: Aug 2010
Location: Ulm, FRG
Posts: 170
Total Downloaded: 0
Hallo,

the next step is to add the deck at the stern part of the hull. This deck was reenforced with 0.2mm Bristolpaper to achive a better stability for the superstructure parts integration. I've changed the colour/color from grey to green to be in line with my first project 956 and 1234. Prior to add the main deck the superstructure on the stern has to be installed. There is a mistake in the design of the formers - thus a correction was made and additional formers were designed to support the superstructure. Details of the structure were installed prior to integration to the hull.
The main deck was also recoloured and reenforced with the above mentioned Bristolpaper - excluding the ceiling part of the stern superstructure section.
Regards Klaus
Attached Thumbnails
Project 1135, frigate Kriwak I class, Oriel, 1:250-bb_oriel63_006.jpg   Project 1135, frigate Kriwak I class, Oriel, 1:250-bb_oriel63_007.jpg   Project 1135, frigate Kriwak I class, Oriel, 1:250-bb_oriel63_008.jpg   Project 1135, frigate Kriwak I class, Oriel, 1:250-bb_oriel63_009.jpg   Project 1135, frigate Kriwak I class, Oriel, 1:250-bb_oriel63_010.jpg  

Project 1135, frigate Kriwak I class, Oriel, 1:250-bb_oriel63_011.jpg   Project 1135, frigate Kriwak I class, Oriel, 1:250-bb_oriel63_012.jpg   Project 1135, frigate Kriwak I class, Oriel, 1:250-bb_oriel63_013.jpg  
Reply With Quote
  #3  
Old 10-25-2015, 04:29 AM
didibuch didibuch is offline
Member
 
Join Date: Jan 2012
Location: Frankfurt/Germany
Posts: 514
Total Downloaded: 379.18 MB
Hi Klaus,

nice start, the superstructure seems to be very solid.

Regards
Dieter
Reply With Quote
  #4  
Old 10-25-2015, 01:26 PM
Kevin WS's Avatar
Kevin WS Kevin WS is offline
Eternal Member
 
Join Date: Aug 2010
Location: Currently Southern Africa.
Posts: 7,121
Total Downloaded: 425.92 MB
Looking good!

Looking forward to this build!
__________________
The SD40 is 55 now!
Reply With Quote
  #5  
Old 10-25-2015, 01:34 PM
Don Boose's Avatar
Don Boose Don Boose is offline
Member
 
Join Date: Jul 2007
Location: Carlisle, Pennsylvania
Posts: 20,702
Total Downloaded: 424.90 MB
Well done so far.

Don
Reply With Quote
Google Adsense
  #6  
Old 10-26-2015, 12:19 PM
RelloemSualk RelloemSualk is offline
Member
 
Join Date: Aug 2010
Location: Ulm, FRG
Posts: 170
Total Downloaded: 0
Hallo,

@Dieter : yes the hull is very, very stable - and will slightly increase the gross weight (hm)
@Kevin & Don : thanx, this part is easy but it takes longer when adding additional parts.


Today the hull will be finalized. The shell plates (four off, each side) were modified - I've combined the two plates of the stern into one plate. Modellers claim that the last plate is too short - I can't confirm this fault.
The scuttles were cutted out and a copy of the bulls-eye was glued on the rear side of the plate. The last slide shows the hull together with project 956.
Regards Klaus
Attached Thumbnails
Project 1135, frigate Kriwak I class, Oriel, 1:250-bb_oriel63_014.jpg   Project 1135, frigate Kriwak I class, Oriel, 1:250-bb_oriel63_015.jpg   Project 1135, frigate Kriwak I class, Oriel, 1:250-bb_oriel63_016.jpg   Project 1135, frigate Kriwak I class, Oriel, 1:250-bb_oriel63_017.jpg   Project 1135, frigate Kriwak I class, Oriel, 1:250-bb_oriel63_018.jpg  


Last edited by RelloemSualk; 10-26-2015 at 12:20 PM. Reason: typo corrections - typing too fast for that keyboard
Reply With Quote
  #7  
Old 10-27-2015, 11:33 AM
RelloemSualk RelloemSualk is offline
Member
 
Join Date: Aug 2010
Location: Ulm, FRG
Posts: 170
Total Downloaded: 0
Hallo,
Today I'll give a brief overview about the guns. Two AK726 (twin barrel) must be assembled and installed on the stern. I didn't take any slides (to show individual steps) during the assembly because I was not sure if I would come to an acceptable result. Additional supports and reenforcements were helpful during the process and some details were added. The twin barrel is movable in elevation, the turret is turnable.
Regards Klaus
Attached Thumbnails
Project 1135, frigate Kriwak I class, Oriel, 1:250-bb_oriel63_024.jpg   Project 1135, frigate Kriwak I class, Oriel, 1:250-bb_oriel63_025.jpg   Project 1135, frigate Kriwak I class, Oriel, 1:250-bb_oriel63_026.jpg   Project 1135, frigate Kriwak I class, Oriel, 1:250-bb_oriel63_027.jpg  
Reply With Quote
  #8  
Old 10-27-2015, 11:42 AM
Tim Crowe's Avatar
Tim Crowe Tim Crowe is offline
Member
 
Join Date: Sep 2008
Location: Wellingborough, U.K.
Posts: 4,714
Total Downloaded: 316.45 MB
Nice work on the guns

Tim
Reply With Quote
  #9  
Old 10-28-2015, 12:24 PM
RelloemSualk RelloemSualk is offline
Member
 
Join Date: Aug 2010
Location: Ulm, FRG
Posts: 170
Total Downloaded: 0
Hallo,

@Tim, thanx - it was hard work

today I'll continue with the superstructure of the VDS located on the stern. The structure is composed of two sections, both having a skeleton as support. Two hinges were added to the VDS stern door. Several structural attachments were available to complete the structure and I could not resist to add handrails.
Regards Klaus
Attached Thumbnails
Project 1135, frigate Kriwak I class, Oriel, 1:250-bb_oriel63_019.jpg   Project 1135, frigate Kriwak I class, Oriel, 1:250-bb_oriel63_020.jpg   Project 1135, frigate Kriwak I class, Oriel, 1:250-bb_oriel63_021.jpg   Project 1135, frigate Kriwak I class, Oriel, 1:250-bb_oriel63_022.jpg   Project 1135, frigate Kriwak I class, Oriel, 1:250-bb_oriel63_023.jpg  

Project 1135, frigate Kriwak I class, Oriel, 1:250-bb_oriel63_028.jpg   Project 1135, frigate Kriwak I class, Oriel, 1:250-bb_oriel63_029.jpg   Project 1135, frigate Kriwak I class, Oriel, 1:250-bb_oriel63_030.jpg   Project 1135, frigate Kriwak I class, Oriel, 1:250-bb_oriel63_031.jpg  
Reply With Quote
  #10  
Old 10-28-2015, 01:06 PM
dje's Avatar
dje dje is offline
Member
 
Join Date: Dec 2014
Posts: 307
Total Downloaded: 0
that diorama look already really nice !
looking forward your work.
__________________
On: Gpm neubaufahrzeug
Still not dead: Gpm mi 4,Gpm jagdpanther,
Done: Mod hobby typ 97,Wak b1bis,Gpm ob3,Modelik vbl, Gpm do335,Halinski p39,Modelik flak 36,Modelik t27
Reply With Quote
Google Adsense
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -6. The time now is 02:09 AM.


Powered by vBulletin®
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.

Parts of this site powered by vBulletin Mods & Addons from DragonByte Technologies Ltd. (Details)
Copyright © 2007-2023, PaperModelers.com