#1
|
|||
|
|||
USS Arizona - Digital Navy
Hello Everyone,
It is with great trepidation that I start this thread on my build of Digital Navy's USS Arizona. This project is already 19 months old and as you see from my pictures I am not that far into it. It took me 9 months to get the courage to printout the plans and it has taken me 10 more months to finish the internal hull frame work. I was gifted this model by one of our fine members as motivation to join the ship building realm. The subject matter needs no introduction. I could not hope to say anything new that has not already been said about this Ship. Hopefully I will find the time and motivation to move this build forward at a quicker pace in the upcoming months. I used 2mm Balsa wood for the main hull former as I couldn't find a piece of cardboard long enough and I didn't want a joint in the middle to act as a weak spot. I think the lower frame I went a little to think on the cross pieces as I had to do a lot of cutting to make the joints fit correctly. I started the hull plating last night and do not have photos of that yet. If anyone has insight as to how to keep them from waving, I am all ears. Thank you for checking in. Comments and instructional critiques welcome. Darren
__________________
Darren |
Google Adsense |
#2
|
||||
|
||||
I'm glad to see that you are undertaking this project. Everything looks shipshape so far.
The balsa should provide for a smooth hull, although as evidence that full-sized ships are not immune from waving hull plating, I submit this image of the Liberty Ship SS John W. Brown, aboard which I had the pleasure to travel on the Chesapeake Bay last Saturday. Of course, armored hulls may be somewhat less susceptible to this sort of dishing. Don |
#3
|
||||
|
||||
I am learning from your technique to improve my work. I will follow your thread.
__________________
Chaiwat Kosatanakom (Jack, the papermann) Aircraft Paper Designer & Modeler "Flying 3 D Paper Airplane Model Inventor" |
#4
|
|||
|
|||
I built the near sister Oklahoma using more or less the same techniques, it's posted here.
|
#5
|
|||
|
|||
Thanks everyone for the encouragement. I will try to keep things rolling and hopefully I will learn a few things along the way.
Don, Thanks for the visual. It makes me feel a little better, but I think the heavier plate on a Battleship was a little less prone to waves. Here are couple of photos from my first few bottom plates. I am wondering if I printed them on too thin of paper. Perhaps the side plates will go on slightly thicker stock to provide some rigidity.
__________________
Darren |
Google Adsense |
#6
|
||||
|
||||
Will be watching this one. This kit builds into a very nice representation of the Grand Ole Girl.
Rick |
#7
|
|||
|
|||
Thanks Rick. I hope I can do this kit justice.
Sorry no pictures for this post. I printed the bottom out on slightly thicker stock and it definitely helped the "waving" i was experiencing earlier. I will post pictures when I get further along the bottom. Now I have to decide if I just overlay the thinner sections or cut them out and replate with the thicker material. Darren
__________________
Darren |
#8
|
||||
|
||||
I hope you enjoy your "Arizona".
Digital Navy used to offer 2 versions, the original and then later an enhanced version. Maybe they still do. But my second project as a paper modeler was the original version. I learned an awful lot about modeling with that ship, and it took me three years. I'll follow along with your work. Mike |
#9
|
|||
|
|||
Thank you Mike,
Any advice or pointers you want to give during my build feel free to do so. You are a master of ships. Darren
__________________
Darren |
#10
|
|||
|
|||
Hello Everyone,
Was able to spend a bit of time last night on the plates. It definately helped moving to a slightly thicker stock. If you look at my pictures from earlier and compare them with these you will note the lack of "waving" on these plates. I was happy with the compound curving that is necessary as you get to the bow. I will, at some point, decide if I am ok with the seams or if I should fill, sand, paint and repeat as necessary. I also attached a photo of the construction page from my USS Arizona book. I noted that the construction started right around the time that Europe exploded into WW1. Thanks for checking in. Comments and advice is welcome. Darren
__________________
Darren |
Google Adsense |
|
|