PaperModelers.com

Go Back   PaperModelers.com > Card Models > Model Builds > Ships and watercraft

Reply
 
Thread Tools Display Modes
  #31  
Old 04-03-2021, 03:58 PM
catopower's Avatar
catopower catopower is offline
Member
 
Join Date: Oct 2014
Location: San Francisco Bay Area
Posts: 60
Total Downloaded: 10.08 MB
Thanks for the nice comments, Radek.

I've been extremely neglectful about posting here, I see. But, I did set the model aside to deal with some family matters and then my wooden model projects(!).

I'm actually quite close to completing this Hanse Kogge von Bremen kit, so it's time to put some more focus on it and get it done.

Lately, I've been discovering parts on the sheets that should have been added to the model earlier. I had to dig back through the instruction images to find out where they go, and mostly found them.

However, I did discover some parts that the instructions missed. But, I manged to figure out where they went and got them into place.

Now, aside from the various little doo-dad parts, I'm starting to deal with more rigging issues. And, since the linen thread that comes with the kit is pure white, I've started dying it in preparation for use on the model. I've mostly used some wood dye to color the line. For darker, tarred line, I happen to have a jar of the old Floquil Marine Colors Dark Stockholm Tar Rigging Stain. Mostly, turns the line a dark brownish gray.
Attached Thumbnails
Bremen Cog - 1/72 scale Shipyard kit-img_1825.jpg   Bremen Cog - 1/72 scale Shipyard kit-img_1826.jpg   Bremen Cog - 1/72 scale Shipyard kit-img_1829.jpg   Bremen Cog - 1/72 scale Shipyard kit-img_1832.jpg   Bremen Cog - 1/72 scale Shipyard kit-img_2280.jpg  

Bremen Cog - 1/72 scale Shipyard kit-img_2302.jpg   Bremen Cog - 1/72 scale Shipyard kit-img_2301.jpg   Bremen Cog - 1/72 scale Shipyard kit-img_2303.jpg   Bremen Cog - 1/72 scale Shipyard kit-img_2304.jpg   Bremen Cog - 1/72 scale Shipyard kit-img_2305.jpg  

Bremen Cog - 1/72 scale Shipyard kit-img_2308.jpg   Bremen Cog - 1/72 scale Shipyard kit-img_2309.jpg  
__________________
Clare
He's a --> HE

Blog: shipmodeler.wordpress.com
Reply With Quote
  #32  
Old 04-07-2021, 12:00 AM
catopower's Avatar
catopower catopower is offline
Member
 
Join Date: Oct 2014
Location: San Francisco Bay Area
Posts: 60
Total Downloaded: 10.08 MB
Yesterday, I added the last of the major structural components to the cog model. Specifically, the parts that are supposed to represent the ends of beams that on the real ship pierce the hull planking and stick out slightly.

Of course, on a card model, these are made up of several layers of small parts. 48 parts make up the 12 beam ends.

Because these are made of moderately thick cardboard, which likes to delaminate, I soaked each assembly with a couple drops of thin CA glue. This wicks into the card stock and hardens to a plastic-like consistency. I was then able to file down and paint the surfaces, which seemed to work pretty well.
Attached Thumbnails
Bremen Cog - 1/72 scale Shipyard kit-img_2331.jpg   Bremen Cog - 1/72 scale Shipyard kit-img_2332.jpg  
__________________
Clare
He's a --> HE

Blog: shipmodeler.wordpress.com
Reply With Quote
  #33  
Old 04-09-2021, 10:46 PM
catopower's Avatar
catopower catopower is offline
Member
 
Join Date: Oct 2014
Location: San Francisco Bay Area
Posts: 60
Total Downloaded: 10.08 MB
It's now time to turn to masting and rigging of the model. For Shipyard kits in particular, the model stops being a card model and becomes more like a wooden ship kit. The kit provides dowels for the mast and yardarm and I'm mostly using these materials.

For rigging, this boxed kit includes linen rigging line, which is very good, but it's plain white in color. I've been coloring the line to be used for the standing rigging (stays, shrouds, etc) using some old Floquil brand rigging stain. I've had this stuff in storage for 20 years and it took a little mixing, but it's still good. The color is called Dark Stockholm Tar.

For the running rigging, essentially the sail handling lines, I was hoping I had some Floquil Light Stockholm tar rigging stain, but I couldn't find any. Instead, I just used some wood dye, mixed to give just about the right color to the line.


As for shaping the masts, they have this kind of three-stepped appearance, with two "shoulders" for the stays to rest on. Rather than try to shape the single mast piece provided in the kit, I decided to use separate pieces of appropriate diameters inserted into holes drilled into the ends of the mast pieces.
Attached Thumbnails
Bremen Cog - 1/72 scale Shipyard kit-img_2324.jpg   Bremen Cog - 1/72 scale Shipyard kit-img_2327.jpg   Bremen Cog - 1/72 scale Shipyard kit-img_2325.jpg   Bremen Cog - 1/72 scale Shipyard kit-img_2328.jpg  
__________________
Clare
He's a --> HE

Blog: shipmodeler.wordpress.com
Reply With Quote
  #34  
Old 04-09-2021, 11:03 PM
catopower's Avatar
catopower catopower is offline
Member
 
Join Date: Oct 2014
Location: San Francisco Bay Area
Posts: 60
Total Downloaded: 10.08 MB
Next, I used Golden Oak stain on the mast. While that was drying, I added the bolt ropes to the sails.

Today, I laced the bonnet (lower sail piece) to the main sail. It took a long time to do, but wasn't difficult.

To help keep the holes in the sail large enough to pass the small rigging line through, I took a sewing needle and glued it into a handle. Sort of a modeler's marlin spike. Later, I also cut open the eye of a needle and mounted that into the other end, so I can lightly grab rigging lines with it too.
Attached Thumbnails
Bremen Cog - 1/72 scale Shipyard kit-img_2337.jpg   Bremen Cog - 1/72 scale Shipyard kit-img_2335.jpg   Bremen Cog - 1/72 scale Shipyard kit-img_2333.jpg   Bremen Cog - 1/72 scale Shipyard kit-img_2346.jpg   Bremen Cog - 1/72 scale Shipyard kit-img_2347.jpg  

Bremen Cog - 1/72 scale Shipyard kit-img_2349.jpg   Bremen Cog - 1/72 scale Shipyard kit-img_2350.jpg  
__________________
Clare
He's a --> HE

Blog: shipmodeler.wordpress.com
Reply With Quote
  #35  
Old 04-12-2021, 10:17 PM
catopower's Avatar
catopower catopower is offline
Member
 
Join Date: Oct 2014
Location: San Francisco Bay Area
Posts: 60
Total Downloaded: 10.08 MB
Kind of a small update here, but an update none the less...

Over the past couple days, I finished making the mast and shaping the yardarm.

With the yardarm done, I laced the sail to it. Like lacing the bonnet to the main sail, it took a little while. But, the results were good and I'm happy with how it went.

I'm now preparing the rigging line for the next step, which is to add the shrouds to the mast. This includes attaching the shrouds, turning each around a deadeye, and then reeving the lanyards through the deadeyes to secure them into place.

Looks like I'm also ready to add the reefing points to the sail. These are short pieces of rope used to tie up part of the sail to the yardarm to reduce the sail area in heavy winds.

The kit instructions simplify this task a bit by attaching separate pieces of riggign line to both sides of the sail. I'm normally used to threading a single piece of line through the sail. Following the method shown in the instructions means that I don't have to poke holes in the sail.
Attached Thumbnails
Bremen Cog - 1/72 scale Shipyard kit-img_2358.jpg   Bremen Cog - 1/72 scale Shipyard kit-img_2359.jpg   Bremen Cog - 1/72 scale Shipyard kit-img_2360.jpg  
__________________
Clare
He's a --> HE

Blog: shipmodeler.wordpress.com
Reply With Quote
Login to remove ads
  #36  
Old Yesterday, 12:55 AM
catopower's Avatar
catopower catopower is offline
Member
 
Join Date: Oct 2014
Location: San Francisco Bay Area
Posts: 60
Total Downloaded: 10.08 MB
I added most of the reefing points on the sail yesterday and finished them up today. This method of attaching reefing points actually has some advantages. It's not difficult to do and since they're glued on, they "hang" perfectly. Threaded reefing points have a tendency to float unrealistically, and you have to treat them with some kind of glue and maybe some ironing to get the correct results.
Attached Thumbnails
Bremen Cog - 1/72 scale Shipyard kit-img_2364.jpg   Bremen Cog - 1/72 scale Shipyard kit-img_2370.jpg   Bremen Cog - 1/72 scale Shipyard kit-img_2361.jpg  
__________________
Clare
He's a --> HE

Blog: shipmodeler.wordpress.com
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -6. The time now is 08:57 PM.


Powered by vBulletin®
Copyright ©2000 - 2021, Jelsoft Enterprises Ltd.
Resources saved on this page: MySQL 10.00%
Parts of this site powered by vBulletin Mods & Addons from DragonByte Technologies Ltd. (Details)
Copyright © 2007-2020, Paper Modelers.com