PaperModelers.com

Go Back   PaperModelers.com > Card Models > Model Builds > Vintage Models

Reply
 
Thread Tools Display Modes
  #1  
Old 05-19-2019, 04:22 AM
Robert Woolley's Avatar
Robert Woolley Robert Woolley is offline
Member
 
Join Date: Jan 2013
Location: Newcastle
Posts: 503
Total Downloaded: 102.95 MB
Imagerie D’Epinal La Locomotive and Tender

Here is another train from Imagerie D'Epinal. This one is much more detailed than the one I made previously. I think it is a model of a French Buddicom locomotive. It is pretty close to the photo I found on the net.
The detail is pretty good. I was very impressed with the artwork and the fit of the parts. The tolerances were very tight. The only part that didn’t fit well was the wheel arch that had to meet the curve of the boiler. It required a good deal of trimming to fit properly.
It wasn’t hard to build but it was hard figuring out where everything went. The parts are put wherever they fit on the page and don’t necessarily relate to the parts nearby. They are all marked with letters, so in theory you must have to match letter to letter. However many of the letters are illegible. Perhaps on the original they could be read. I printed on A4 card. I don’t know what size the original was.
Even when you figure out where the parts go, without a knowledge of the mechanics of steam engines it would be puzzling as to how they should go together. I don’t know what references were like back when these were published but I don’t imagine they would have been adequate to show how things go.
The only departure I made to the original design was in the wheels. I build them up to look solid. The original had a loop of paper glued to a the outside of a flat disc to represent the surface of the wheel that touches the tracks. It just looked weird and was hard to get round.
The driver supplied with the locomotive looked to small. The tender had bigger figures that looked about right. You can see both of them in the pictures.
Over all a fun build and I am pleased with the result.
Attached Thumbnails
-97064a3f-456c-42e3-9f4b-3dd62ae4dc83.jpg   -0dbdda4f-314b-46c0-af30-bfc357232267.jpg   -c221b5c5-ce29-4b93-ab3a-87acda94e8e5.jpg   -be249b37-60b7-4ac7-a203-548de1a1faff.jpg   -e11b568b-8695-46fd-a8ba-a8315dfbf662.jpg  

-a65ac848-1959-471f-85ae-5bd12d751a88.jpg   -979c27fa-a608-49ca-963a-d9c8f8320855.jpeg   -d3b76942-054c-422f-87c1-51865091bca4.jpg   -4164e27b-c64e-40f9-ae7b-d47653d94633.jpg  
Reply With Quote
Google Adsense
  #2  
Old 05-19-2019, 05:04 AM
SCEtoAUX's Avatar
SCEtoAUX SCEtoAUX is offline
Member
 
Join Date: Jul 2007
Location: USA
Posts: 7,800
Total Downloaded: 567.16 MB
Looks very good. You did a good job in figuring out where the parts go.

I have built a few of those Imagrie D'Epinal models. It is an all out process to first clean up the scans since most have a severe color cast and decide just how the colors should look. Then you need to decide how big to print them since most do not have any indication of the scale. Then as you noted you need to figure out exactly where the various parts that are scattered throughout the sheet go during the construction.

I have tried to transcribe some of the text in order to get a translation to see if there are any good hints as to the steps needed to make the models. I have also tried capturing the areas with the text and saving as a picture to try some OCR. The results have been interesting to say the least.
__________________
~Doug~
AC010505 EAMUS CATULI! Audere est Facere THFC 19**-20** R.I.P. it up, Tear it up, Have a Ball
Reply With Quote
  #3  
Old 05-19-2019, 05:18 AM
Robert Woolley's Avatar
Robert Woolley Robert Woolley is offline
Member
 
Join Date: Jan 2013
Location: Newcastle
Posts: 503
Total Downloaded: 102.95 MB
Thanks Doug. On this one I used gimp to remove the discolouration around the parts. The model in the pictures was made using a print I made later. Again I used gimp, this time to erase all of the big identification letters that were printed in visible areas of the parts.
This model was actually my second attempt. At first I tried using the tabs drawn on the parts, but as the tolerances were so tight I managed to slightly twist the model down its length. On the second attempt I didn’t use the tabs. Instead I glued parts that formed shapes to thicker card and built around them. This was much quicker and easier than cutting hundreds of little tabs.
Reply With Quote
  #4  
Old 05-19-2019, 06:16 AM
eatcrow2's Avatar
eatcrow2 eatcrow2 is offline
Member
 
Join Date: Jul 2007
Location: Santa Monica, CA
Posts: 2,590
Total Downloaded: 2.23 GB
Excellent work!
Reply With Quote
  #5  
Old 05-19-2019, 06:19 AM
southwestforests's Avatar
southwestforests southwestforests is offline
Member
 
Join Date: Feb 2011
Location: On the edge of the river valley
Posts: 1,474
Total Downloaded: 5.88 MB
Looks like a satisfying end to a modeling adventure.
__________________
Screw the rivets, I'm building for atmosphere, not detail.
later, F Scott W
Reply With Quote
Google Adsense
  #6  
Old 05-19-2019, 07:22 AM
patriciaeureka patriciaeureka is offline
Member
 
Join Date: Feb 2012
Posts: 78
Total Downloaded: 41.75 MB
and the wagon
wagon gc epinal by patricia m, sur Flickr
Reply With Quote
  #7  
Old 05-19-2019, 07:23 AM
patriciaeureka patriciaeureka is offline
Member
 
Join Date: Feb 2012
Posts: 78
Total Downloaded: 41.75 MB
gc locomotive by patricia m, sur Flickr
loco & tender
tender by patricia m, sur Flickr
Reply With Quote
  #8  
Old 05-19-2019, 12:26 PM
MarvinDalek MarvinDalek is offline
Member
 
Join Date: Apr 2019
Posts: 8
Total Downloaded: 3.64 MB
The originals are Petites- 23 x 30 cm, Moyennes- 29.5 x 40.5 cm and Grandes- 49 x 39 cm. (small, medium and large)
Reply With Quote
  #9  
Old 05-19-2019, 02:02 PM
Philip's Avatar
Philip Philip is offline
Member
 
Join Date: Dec 2007
Location: Croydon, UK
Posts: 2,842
Total Downloaded: 99.03 MB
A lovely model, and well-executed.
__________________
Give me a pigfoot and a bottle of beer.
On Flickr: https://www.flickr.com/photos/153077...57692694097642
Reply With Quote
  #10  
Old 05-23-2019, 09:31 AM
MarvinDalek MarvinDalek is offline
Member
 
Join Date: Apr 2019
Posts: 8
Total Downloaded: 3.64 MB
Is this the locomotive?


https://commons.wikimedia.org/wiki/F...oudroyante.jpg
Reply With Quote
Google Adsense
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -6. The time now is 12:55 AM.


Powered by vBulletin®
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.

Parts of this site powered by vBulletin Mods & Addons from DragonByte Technologies Ltd. (Details)
Copyright © 2007-2023, PaperModelers.com