PaperModelers.com

Go Back   PaperModelers.com > Card Models > Model Builds > Aviation

Reply
 
Thread Tools Display Modes
  #1  
Old 12-28-2020, 09:33 PM
kwc kwc is offline
Member
 
Join Date: Jun 2009
Location: Nevada
Posts: 119
Total Downloaded: 27.77 MB
Dmitry Udalov's Su-27SKM in 1:72

Quite a few years ago, I decided I wanted to build a Flanker (and asked around for some recommendations, as you can probably find in my posting history). I started working on the Su-27 from P.Model but became dissatisfied with it because it lacked detail and didn't seem that accurate.

So then I convinced myself that I could build one of Dmitry Udalov's Flankers (designed in 1:33) reduced to my preferred scale of 1:72. The one I chose was the Su-27SKM, and I bought it from Ecardmodels. It isn't available there anymore but I think it can be found at бумажные модели.

I made some decent progress on the model, but at some point I got a pretty bad water or glue stain on it and then couldn't get my printer to print a replacement part with matching colors (the ink cartridges had probably been changed). So I scrapped what I had and started over with a new printout, but because of the impact on morale as well as other things I had going on, I didn't make it very far into the second attempt before shelving it for a long while.

I finally started working on it again earlier this year, and I think I've made enough progress (significantly more than in my first attempt) that I can show what I have.

This model seems well-engineered; a lot of the interior structure is very elaborately designed. I'm sure this is much appreciated at the intended 1:33, but at 1:72 (less than half of the original), it sometimes feels like overkill, although it is still satisfying to make everything come together.

Dmitry Udalov's Su-27SKM in 1:72-pxl_20201120_102332420.jpgDmitry Udalov's Su-27SKM in 1:72-pxl_20201122_125015817.jpg

As it takes shape, you start getting an idea of how big the Su-27 is...

Dmitry Udalov's Su-27SKM in 1:72-pxl_20201209_005533091.jpgDmitry Udalov's Su-27SKM in 1:72-pxl_20201210_021653477.jpgDmitry Udalov's Su-27SKM in 1:72-pxl_20201223_034915816.jpg

I'm trying to avoid a repeat of the earlier disaster by keeping my hands dry and clean and being careful where I set things down. Some minor damage has already occurred, but so far I've been able to hide it adequately with some manual coloring.

I'm not the most talented builder and the reduced scale is only making it harder, so there are a lot of imperfections in my build in general. (For one thing, I think the entire fuselage is a little crooked, but I'm hoping that won't really be noticeable when the whole thing is done.) I found another build of this Su-27SKM by na120372 (in 1:33) that is probably a much better demonstration of how well it can be built.

Kevin
Reply With Quote
Login to remove ads
  #2  
Old 12-29-2020, 06:35 AM
MacSongLi's Avatar
MacSongLi MacSongLi is offline
Member
 
Join Date: May 2012
Location: Ontario, Canada
Posts: 4,860
Total Downloaded: 457.88 MB
Kevin,

I'd say that you're off to a great start. I purchased a copy of this kit, but haven't built it yet. I thought that it would be a lot more sturdy if the formers were made 1mm thick (assuming the build at 1/33 scale). Your 1/72 build looks great.

Keep up the great work.

Gary
__________________
"Fast is fine, but accuracy is everything"
- Wyatt Earp
Reply With Quote
  #3  
Old 01-19-2021, 12:43 AM
kwc kwc is offline
Member
 
Join Date: Jun 2009
Location: Nevada
Posts: 119
Total Downloaded: 27.77 MB
Some work inside the cockpit:

Dmitry Udalov's Su-27SKM in 1:72-pxl_20210118_215422635.jpgDmitry Udalov's Su-27SKM in 1:72-pxl_20210118_215438975.jpg

I thought there were some slight issues with the geometry as designed after comparing it with some photos, so I made some parts to raise the control stick up a bit. Seeing na120372's build also made me want to try adding some seat belt detail, which I think turned out pretty decent.

I still have to do something for the HUD, and then I want to try vacuum-molding a canopy (which is something I've never done before, other than some recent quick experiments), so I'm hoping I can pull that off well.

Kevin
Reply With Quote
  #4  
Old 01-19-2021, 12:44 AM
YOAVHOZMI YOAVHOZMI is offline
Member
 
Join Date: Jun 2013
Location: kiryat yam
Posts: 4,084
Total Downloaded: 5.90 MB
nice job

YOAV
Reply With Quote
  #5  
Old 01-19-2021, 05:42 AM
MacSongLi's Avatar
MacSongLi MacSongLi is offline
Member
 
Join Date: May 2012
Location: Ontario, Canada
Posts: 4,860
Total Downloaded: 457.88 MB
Great looking pilot's office. The seat belt detailing adds very nicely to the project.

Gary
__________________
"Fast is fine, but accuracy is everything"
- Wyatt Earp
Reply With Quote
Login to remove ads
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -6. The time now is 07:16 AM.


Powered by vBulletin®
Copyright ©2000 - 2021, Jelsoft Enterprises Ltd.
Resources saved on this page: MySQL 10.53%
Parts of this site powered by vBulletin Mods & Addons from DragonByte Technologies Ltd. (Details)
Copyright © 2007-2020, Paper Modelers.com