#11
|
||||
|
||||
Wings
The wings consist of 3 sections. Center section and two outer sections with a slight dihedral.
parts and spar/frames I used two small rulers and clamps to keep the glued edge from curling. Outer wing sections center wing section wings are joined and ready. Isaac
__________________
My gallery [http://www.papermodelers.com/gallery...v-r-6&cat=500] Recent buildsMeteor F1, Meteor F8, Mig-Ye8, NA Sabre, A-4E Skyhawk,Mig-15 red, Mig-17 repaint |
#12
|
||||
|
||||
Coming a along quite nicely Isaac.
Gary
__________________
"Fast is fine, but accuracy is everything" - Wyatt Earp Design Group Alpha https://ecardmodels.com/vendors/design-group-alpha |
#13
|
|||
|
|||
Looks very nice Isaac, hope to see the R version soon.
ShalomMor |
#14
|
||||
|
||||
Shalom
Me too. Murph has offered to modify his J21 prop version to the R jet version. I am looking forward to it. Thanks Isaac
__________________
My gallery [http://www.papermodelers.com/gallery...v-r-6&cat=500] Recent buildsMeteor F1, Meteor F8, Mig-Ye8, NA Sabre, A-4E Skyhawk,Mig-15 red, Mig-17 repaint |
#15
|
||||
|
||||
Wings joined to fuselage
__________________
My gallery [http://www.papermodelers.com/gallery...v-r-6&cat=500] Recent buildsMeteor F1, Meteor F8, Mig-Ye8, NA Sabre, A-4E Skyhawk,Mig-15 red, Mig-17 repaint |
Google Adsense |
#16
|
||||
|
||||
Twin booms
Being a pusher propeller design, required attaching the tail surfaces in a way to avoid being struck by the prop. A common design was the use of a twin boom.
parts assembled add wood to the wing underside to attach the main landing gear attached to the wing and done Note: This is a very fast build to see if it can be converted to a jet. So I did not care too much about the appearance or rough edges. This also exposed the areas of concern regarding fit and looks since I up scaled it from 1/48 to 1/33. Isaac
__________________
My gallery [http://www.papermodelers.com/gallery...v-r-6&cat=500] Recent buildsMeteor F1, Meteor F8, Mig-Ye8, NA Sabre, A-4E Skyhawk,Mig-15 red, Mig-17 repaint |
#17
|
||||
|
||||
Tail surfaces
Here are the vertical tin fins and the horizontal one piece fin
The vertical fins have added piece of wood stick in order to glue them to the booms without falling apart. I would say for a large 1/33 scale version this is a weak point of the design and needed that extra support. For 1/48 scale and smaller, it is probably OK. ready attached Isaac
__________________
My gallery [http://www.papermodelers.com/gallery...v-r-6&cat=500] Recent buildsMeteor F1, Meteor F8, Mig-Ye8, NA Sabre, A-4E Skyhawk,Mig-15 red, Mig-17 repaint |
#18
|
||||
|
||||
Status
__________________
My gallery [http://www.papermodelers.com/gallery...v-r-6&cat=500] Recent buildsMeteor F1, Meteor F8, Mig-Ye8, NA Sabre, A-4E Skyhawk,Mig-15 red, Mig-17 repaint |
#19
|
||||
|
||||
Landing gear
There is nothing much here. No detail at all.
Wheels are laminated and sanded card discs gear in place on gear Isaac
__________________
My gallery [http://www.papermodelers.com/gallery...v-r-6&cat=500] Recent buildsMeteor F1, Meteor F8, Mig-Ye8, NA Sabre, A-4E Skyhawk,Mig-15 red, Mig-17 repaint |
#20
|
||||
|
||||
Prop and engine exhaust
__________________
My gallery [http://www.papermodelers.com/gallery...v-r-6&cat=500] Recent buildsMeteor F1, Meteor F8, Mig-Ye8, NA Sabre, A-4E Skyhawk,Mig-15 red, Mig-17 repaint |
Google Adsense |
Thread Tools | |
Display Modes | |
|
|