|
|
|
#21
11-29-2023, 01:23 AM
|
||||
|
||||
|
And further ...
The inner roof, with a length of 28 cm, is very large... the rear window is inserted and rounded... Glue with small paper tabs...and let dry thoroughly. Sincerely Kurt 
|
|
#22
11-29-2023, 11:53 PM
|
||||
|
||||
|
Hello
 Now I'm starting to install the inner roof, first gluing it in one corner... ... and continue to move forward step by step... ... until the roof fits halfway, a difficult task! Sincerely Kurt
|
|
#23
12-01-2023, 12:55 AM
|
||||
|
||||
|
And further ...
... with the middle part ... first glue it on one side ... ... then connect the second side and the cut again with small tabs ... not perfect but I'm almost satisfied, but who is perfect? Not me  Best regards Kurt
|
|
#24
12-01-2023, 11:55 PM
|
||||
|
||||
|
now continue...
... with the front inner roof part ... which I pre-round on foam rubber using round wood ... ... and glue again with small tabs ... first fix it to the rear tabs and let it dry. Best regards Kurt
|
|
#25
12-03-2023, 05:55 AM
|
||||
|
||||
|
And further ...
Connect the cut edge with small tabs... and glue forward step by step. So the inner roof is installed, the three-part division made installation much easier, but it was still a tricky matter. And continue with the three parts for the dashboard... reinforced with 1 mm cardboard. Sincerely Kurt
|
| Google Adsense |
|
#26
12-05-2023, 12:19 AM
|
||||
|
||||
|
Hello
I insert a 3 mm cardboard strip into the dashboard... installed in the front... ... and another look backwards. Sincerely Kurt
|
|
#27
12-05-2023, 11:41 PM
|
||||
|
||||
|
Hello everyone !
I would like to thank you for the many likes. Your interest is a good motivation when things aren't going so well And further ..... In contrast to the inner roof, I will put up the outer roof as a whole... which will first be glued together with 70 small tabs... ... I'll start gluing at the back again and gradually move forward. This is where the first inconsistencies emerge. Best regards Kurt
|
|
#28
12-06-2023, 09:07 AM
|
|||
|
|||
|
Good work, have been following along. I wish I had as much time to make such rapid progress with a kit myself.
What's your plan for dealing with any fit issues here?
__________________
Currently in the hanger: Thaipaperwork Martin B-26 'Flak-Bait' In the shipyard: JSC barkentine 'Pogoria' Recently completed: TSMC F-16, S&P Kawanishi N1K1 Kyofu diorama
|
|
#29
12-06-2023, 01:12 PM
|
||||
|
||||
|
good work on the bus Kurt
__________________
David........... Paper modelling gives you a happy high. currently building. c GAZ 51 ALG 17, wagon 111a. unex DH411 excavator and spitfire Mk 9
|
|
#30
12-07-2023, 12:55 AM
|
||||
|
||||
|
Hello Siwi,
My plan is to conceal any fit problems by spatula with thick glue and further .... Now proceed with the gluing further and further forward, a delicate procedure... There are problems at the front, 1. 3 mm are missing at the top, 2. the same with the window pillars, 3. There is also a gap on the side which I will fill with glue. I also had to improvise with the windshield and the result turned out as you can see. Sincerely Kurt
|
| Google Adsense |
 |
|
|
Linear Mode
