PaperModelers.com

Go Back   PaperModelers.com > Card Models > Tips and Tricks

Reply
 
Thread Tools Display Modes
  #1  
Old 06-02-2023, 01:14 PM
ChickenFaceMan ChickenFaceMan is offline
Member
 
Join Date: Sep 2016
Posts: 21
Total Downloaded: 1.29 MB
Coating paper

Hello,
I have some models printed from my printer on paper card stock. A drop of water on the ink, and it bleeds the colors. Is there a spray I can use to coat/seal the paper and protect it? I'm not sure what's best.
Thank you!!!
Reply With Quote
Google Adsense
  #2  
Old 06-02-2023, 02:01 PM
theOshkoshModeler's Avatar
theOshkoshModeler theOshkoshModeler is offline
Member
 
Join Date: May 2023
Location: Oshkosh, WI- the aviation capital of the world!
Posts: 55
Total Downloaded: 84.35 MB
One way I've seen from other modelers (specifically Edwin Rodriguez of Hermercraft) is to 'seal' the paper with a layer of white glue using the face of a credit card.

This should, in theory, not only prevent the print from damage but also allow for you to apply a gloss or matte spray after finishing the model (should you want to) without the spray being absorbed by the paper.

I've tried this method a few times and I absolutely hate it. Too much of a mess and the paper starts to warp as it soaks up the glue. Maybe it's because I use clear glue instead of white :P.

There's probably other ways that work a lot better, but that's pretty much the only method I've seen to 'seal' paper.

__________________
Current / Upcoming Projects-
Mitsubishi F-1 50th Anniversary
Panavia Tornado
Reply With Quote
  #3  
Old 06-02-2023, 02:06 PM
theOshkoshModeler's Avatar
theOshkoshModeler theOshkoshModeler is offline
Member
 
Join Date: May 2023
Location: Oshkosh, WI- the aviation capital of the world!
Posts: 55
Total Downloaded: 84.35 MB
Quote:
Originally Posted by theOshkoshModeler View Post
One way I've seen from other modelers (specifically Edwin Rodriguez of Hermercraft) is to 'seal' the paper with a layer of white glue using the face of a credit card.




Here's an example (from Edwin's YT)
__________________
Current / Upcoming Projects-
Mitsubishi F-1 50th Anniversary
Panavia Tornado

Last edited by theOshkoshModeler; 06-02-2023 at 02:10 PM. Reason: Fixed Youtube embed
Reply With Quote
  #4  
Old 06-02-2023, 02:13 PM
theOshkoshModeler's Avatar
theOshkoshModeler theOshkoshModeler is offline
Member
 
Join Date: May 2023
Location: Oshkosh, WI- the aviation capital of the world!
Posts: 55
Total Downloaded: 84.35 MB
Quote:
Originally Posted by theOshkoshModeler View Post
Here's an example (from Edwin's YT)
And that's what I get for trying to embed YouTube my third day on the forum :P
I'll just give you the link instead- Tips for papercraft part 3 - Glossy papercrafts - YouTube
__________________
Current / Upcoming Projects-
Mitsubishi F-1 50th Anniversary
Panavia Tornado

Last edited by theOshkoshModeler; 06-02-2023 at 02:14 PM. Reason: Added link
Reply With Quote
  #5  
Old 06-02-2023, 03:09 PM
rockpaperscissor's Avatar
rockpaperscissor rockpaperscissor is offline
Member
 
Join Date: Dec 2007
Location: The thriving metropolis of Wappingers Falls, NY, USA
Posts: 4,539
Total Downloaded: 127.35 MB
I use Krylon clear satin spray paint to seal my inkjet printed pages before any cutting/folding/gluing takes place. A couple of light coats in different directions to ensure full coverage is all it takes.
__________________
Regards, Don
I don't always build models, but when I do... I prefer paper. Keep your scissors sharp, my friends.
Reply With Quote
Google Adsense
  #6  
Old 06-02-2023, 08:12 PM
Madbrit Madbrit is offline
Member
 
Join Date: Dec 2012
Location: Glendale, California
Posts: 347
Total Downloaded: 82.25 MB
Faced with exactly the same problem I used Krylon Workable Fixative (used to seal layers of chalk pastel). In the US it will be available at Blick and Michael's. Being unaware of your location I'd say that any pastel fixative (spray can version) would serve just as well.

Derek
Reply With Quote
  #7  
Old 06-02-2023, 08:39 PM
-Jim G's Avatar
-Jim G -Jim G is offline
Member
 
Join Date: Jul 2007
Location: St. Paul, Minnesota
Posts: 672
Total Downloaded: 113.01 MB
I have taken to having my models printed on a laser printer instead of using an ink printer. The laser finish I get is resistant to water. It does not run. I pay about $1.50 USD per sheet at FedEx.
__________________
-Jim G
Reply With Quote
  #8  
Old 06-03-2023, 12:05 PM
Siwi Siwi is offline
Member
 
Join Date: May 2012
Location: Southampton, birthplace of the Spitfire
Posts: 1,216
Total Downloaded: 134.16 MB
Laser printing is more water resistant but the weakness of it is that it can crack and rub off, especially if the paper is curved or folded. I also use a clear coat spray, or else decide in advance if I want to paint over the model with acrylics.
__________________
Currently in the hanger: Thaipaperwork Martin B-26 'Flak-Bait'
In the shipyard: JSC barkentine 'Pogoria'
Recently completed: TSMC F-16, S&P Kawanishi N1K1 Kyofu diorama
Reply With Quote
  #9  
Old 06-03-2023, 06:12 PM
CharlieC's Avatar
CharlieC CharlieC is offline
Member
 
Join Date: Jul 2007
Location: Brisbane
Posts: 2,225
Total Downloaded: 16.12 MB
Just about any acrylic spray seems to work. I haven't seen Krylon in Australia for years but the local brands seem to work just fine. With acrylic you get a choice of matt. satin and gloss finishes. I've never used gloss so can't comment on that.

Charlie
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -6. The time now is 04:39 AM.


Powered by vBulletin®
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.

Parts of this site powered by vBulletin Mods & Addons from DragonByte Technologies Ltd. (Details)
Copyright © 2007-2023, PaperModelers.com